1. Core Fault Codes & Solutions
PrimAry Fault Codes
| Code | Description | Troubleshooting Steps |
|---|---|---|
| 0 | Serial Communication Error | - Check communication cables (e.g., traveling cables) between door control board and main controller. - Ensure proper grounding and eliminate EMI sources. |
| 1 | Inverter Overcurrent | - Replace the door control board (PCB). - Inspect motor bearings and door rails for jamming; clean and lubricate. |
| 2 | +12V Undervoltage | - Replace the door control board (PCB). - Test power supply modules and aging capacitors. |
| 3 | Main Circuit Undervoltage | - Verify stability of main power input. - Replace faulty rectifier bridge or capacitors. |
| 4 | CPU Watchdog Error (WDT) | - Restart door control board. - Replace the board if the error persists. |
| 7 | Open/Close Command Logic Error | - Inspect DOQ/DCQ signal lines. - Calibrate control parameters using debugging tools. |
| 9 | Closing Operation Error | - Check door lock contact alignment and mechanical obstructions. - Adjust CLT sensor position. |
| A | Overspeed Detection | - Adjust door speed parameters (e.g., SP03-4.5 for max opening speed). - Inspect encoder wiring or replace the encoder. |
| D | Overload | - Verify motor load (e.g., door rail debris). - Measure line resistance for poor contact. |
| F | Overspeed Check | - Ensure encoder shielding is grounded. - Replace the encoder or recalibrate speed curves. |
2. Sub-Codes (Extended Faults)
| Sub-Code | Description | Troubleshooting Steps |
|---|---|---|
| 4.GS | Door Lock (GS) Anomaly | - Adjust car door dimensions and photoelectric sensor alignment. - Measure door lock circuit resistance (normal <1Ω). |
| 5. | Position Switch Error | - Reposition OLT/CLT switches. - Clean contacts or replace faulty switches. |
| C. | Encoder Error | - Reconnect encoder plugs with proper shielding. - Replace the encoder or control board. |
| E. | DLD Insufficient Margin | - Adjust DLD parameters (e.g., SP01-2.3 for sensitivity). - Inspect mechanical alignment (e.g., door rails). |
| F. | GS Release Indication Error | - Verify door lock timing sequence. - Check for short circuits or breaks in safety loops. |
3. Fault Code Retrieval (VFGLC/VFGL Series)
-
VFGLC Models (KCD-115X/KCD-116X):
-
Set MON1=1, MON0=0 (real-time faults) or MON0=1 (historical faults).
-
Read codes via DH2/DL2 display.
-
-
VFGL Models (KCD-100X):
-
Enter debug mode: SET1=E, SET0=1.
-
Toggle MON1=1 and MON0=0/8 to view real-time or latched fault codes.
-
4. Maintenance & Optimization Guidelines
1. Hardware Maintenance
-
Mechanical Cleaning: Regularly remove debris from door rails and lubricate motor bearings.
-
Wiring Inspection: Prioritize encoder connectors, door lock circuits (41DG), and safety edge wiring.
2. Parameter Calibration
-
Speed Curve Adjustment: Configure SP02-6.7 (max closing speed) and SP03-4.5 (max opening speed).
-
Self-Learning Function: Execute door auto-learning for position feedback calibration (applicable models).
3. Common Crash Causes
-
Encoder Issues: Signal loss or loose connectors (30% of crashes).
-
Power Interference: Test main circuit capacitors and voltage-balancing resistors.
Safety Notes:
-
Always disconnect power before handling high-voltage circuits.
-
Backup parameters before adjustments to prevent system errors.
Compiled by www.felevator.com technical team. Repost with attribution.
